All Categories > Product Help > Heat Applied Graphics > Heat Transfer Application Instructions

Heat Transfer Application Instructions

3D Application Instructions

Set temperature at 340-350 degrees Fahrenheit. Set pressure at medium to heavy. Print 8-10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion.

Updated 5 years ago by Matt Cohen

3D Puff Application Instructions

Set temperature at 330 degrees Fahrenheit. Set pressure at heavy. Print 8 seconds. Peel gently and immediately while hot. These instructions might vary depending on the transfer machine being used fo…

Updated 5 years ago by Nathan Reedy

Applique Application Instructions

With Heat Press Machine – 350 degrees for 20 seconds or 375 degrees for 15 seconds with medium pressure. Use of a protective cloth is recommended. Click Here For Video Instructions...

Updated 4 years ago by Nathan Reedy

Cold Peel Application Instructions

Set temperature at 375 degrees Fahrenheit. Set pressure at medium. Print for 12 seconds. Rub surface with eraser or cloth. Allow to cool completely/peel cold. Pull transfer paper from side to side or…

Updated 4 years ago by Nathan Reedy

Cold Peel Face Mask Application Instructions

Pre-press garment; 5-7 seconds. Set temperature at 250-300 degrees Fahrenheit. Set pressure to 55-60 lbs (medium/heavy pressure). Print 8-10 seconds. Peel after transfer has cooled down in a continuo…

Updated 4 years ago by Nathan Reedy

ColorTrans Application Instructions

Pre-press garment; 5-7 seconds. Set temperature at 325 degrees Fahrenheit. Set pressure to 55-60 lbs. Print for 7 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion. Click H…

Updated 4 years ago by Nathan Reedy

DTF Transfer Application Instructions

Application Instructions Set temperature at 315 degrees Fahrenheit. Set pressure at medium. Print 15 seconds. Peel Cold. Wait until the transfer is cool to the touch and remove the film gently. Cover…

Updated 2 years ago by Nathan Reedy

Foil Application Instructions

Pre press garment for 7 seconds before applying transfer. Set pressure at high. Set temperature at 375 degrees Fahrenheit. Foil designs come with a silicone paper to go over the foil before printing.…

Updated 5 years ago by Nathan Reedy

Foil Roll Application Instructions

First, either apply the above mentioned plastisol heat transfers or direct prints to the garment. Cut the Textile Foil to the desired shape and place it, color side up, over the area chosen to be "fo…

Updated 5 years ago by Nathan Reedy

Full Color (Oversize) Application Instructions

Application Instructions. Place garment on platen with the collar at the top of the press. Make sure collar is off the platen. Place transfer on the garment so that the image begins approximately 1"…

Updated 3 years ago by Nathan Reedy

Full Color Application Instructions

Application Instructions Pre-press garment; 5-7 seconds. Set temperature at 300-315 degrees Fahrenheit. Set to heavy pressure. Print for 7-10 seconds. Peel immediately while hot, in one continuous mo…

Updated 2 years ago by Nathan Reedy

Glitter Application Instructions

Pre-heat garment for 5-10 seconds. Set pressure at medium to high. Set temperature at 350 degrees Fahrenheit. Print 10 seconds. Peel immediately while hot.

Updated 5 years ago by Nathan Reedy

Glow In The Dark Application Instructions

Pre press garment for 7 seconds before applying transfer. Set pressure at Medium-Heavy. Set temperature at 320 degrees Fahrenheit. Print 6-8 seconds. Peel immediately while hot. Hold up to a light or…

Updated 2 years ago by Nathan Reedy

High Definition - Dark Application Instructions

Set temperature at 365-385 degrees Fahrenheit. Set pressure at heavy. A pressing pillow or perfect pad may be needed to achieve the amount of pressure needed. Print 8 to 10 seconds. Peel immediately…

Updated 4 years ago by Nathan Reedy

High Definition - Dark Application Instructions for Manual Heat Press

Set temperature at 375-385 degrees Fahrenheit. Set pressure at medium to heavy. Print 10 to 12 seconds. Rub the back of the design for 5 seconds. Peel slowly. These instructions might vary depending…

Updated 5 years ago by Nathan Reedy

High Definition - Glitter Application Instructions

Set temperature at 385-400 degrees Fahrenheit. Set pressure at heavy. A pressing pillow or perfect pad may be needed to achieve the right amout of pressure. Print 12-15 seconds. Peel Cold (let transf…

Updated 4 years ago by Nathan Reedy

High Definition - Lights Application Instructions

Set temperature at 385-400 degrees Fahrenheit. Set pressure at heavy. A pressing pillow or perfect pad may be needed to achieve the right amount of pressure. Print 8 to 10 seconds. Peel immediately w…

Updated 3 years ago by Nathan Reedy

High Definition With Rhinestone Application Instructions

Transfer HD Transfer Temperature: 385˚ - 400˚F. Pressure: Medium/Heavy 45 - 55 PSI. Time: 8 - 10 Sec. - Hot Peel Immediately. Rhinestones Peel backing from rhinestone transfer and position holes in a…

Updated 5 years ago by Nathan Reedy

Hot Peel (Oversize) Application Instructions

Place garment sideways on platen with neck band just outside the left edge of the lower platen. Place transfer on the garment so that the image begins approximately 1" inside the left edge of the pla…

Updated 3 years ago by Nathan Reedy

Hot Peel 350 Application Instructions

Set temperature at 350 degrees Fahrenheit. Set pressure at heavy. Print 10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion.

Updated 5 years ago by Nathan Reedy

Hot Peel Application Instructions

Set temperature at 390-400 degrees Fahrenheit. Set pressure at medium-heavy. Print 10-12 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion. Click Here For Video Instruction…

Updated 3 years ago by Nathan Reedy

Letter Application Instructions

Preheat bottom pad before applying by locking the top platen down for 60 seconds. This helps the ink to flow properly during the application. Peel desired letters off of release paper, by peeling fro…

Updated 4 years ago by Nathan Reedy

Litho-Glitter Application Instructions

Set temperature at 375 degrees Fahrenheit. Set pressure at medium to high. Print 12-15 seconds. Carefully remove garment from platen and place on a smooth surface. With a soft cloth, rub the transfer…

Updated 5 years ago by Nathan Reedy

Lumi-Trans Application Instructions

Set temperature at 375-385 degrees Fahrenheit. Set pressure at medium to heavy. A pressing pillow or perfect pad may be needed to achieve the right amount of pressure. Print 10 to 12 seconds. Peel im…

Updated 4 years ago by Nathan Reedy

Lumi-Trans Application Instructions For Manual Heat Press

Updated 5 years ago by Nathan Reedy

Mixed Media Application Instructions

Pre-press garment; 5-7 seconds. Peel the white sheet and discard. Place sticky side down on the garment. Set pressure at moderate. Set temperature at 300-330 degrees Fahrenheit. Press 15-20 seconds.…

Updated 4 years ago by Nathan Reedy

Neon Blacklight Application Instructions

Set temperature at 380-385 degrees Fahrenheit. Set pressure at medium to heavy. Print 8-10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion.

Updated 5 years ago by Nathan Reedy

Neon Rhinestud Application Instructions

Set temperature at 335-350 degrees Fahrenheit. Set pressure at medium to heavy. Remove the white plastic backing from the transfer. Place the transfer face up on the fabric. Press for 12-15 seconds.…

Updated 5 years ago by Nathan Reedy

Number Application Instructions

Set temperature at 360 degrees Fahrenheit. Set pressure at medium-heavy. Print 3-5 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion. Click Here For Video Instructions...

Updated 4 years ago by Nathan Reedy

Perfect Peel Application Instructions

Pre-press garment for about 5-7 seconds. Set temperature at 375-385 degrees Fahrenheit. Set pressure to Medium. Print 7-10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion…

Updated 5 years ago by Nathan Reedy

Plush Application Instructions

Application Instructions Pre-press garment for about 5-7 seconds. Set temperature at 375 degrees Fahrenheit. Set pressure to Heavy. Print 10 seconds. Peel immediately while hot, in one continuous, sm…

Updated 5 years ago by Nathan Reedy

Puff Application Instructions

Set temperature at 360-385 degrees Fahrenheit. Place sweatshirt on top of bottom pad for added pressure. Set pressure at medium. Print 6 to 8 seconds. Peel immediately while hot. Pull transfer paper…

Updated 4 years ago by Nathan Reedy

Reversible Sequin Application Instructions

Pre-press garment; 5-7 seconds. Set pressure at moderate. Set temperature at 300-330 degrees Fahrenheit. Cover design with a sheet of parchment paper to protect it from the heat. Press 15-20 seconds.

Updated 5 years ago by Nathan Reedy

Rhinestud Application Instructions

Set temperature at 327 degrees Fahrenheit. Set pressure at medium to heavy. Remove the white plastic backing from the transfer. Place the transfer face up on the fabric. Press for 13 seconds. Let coo…

Updated 4 years ago by Nathan Reedy

Solar Trans Application Instructions

Set temperature at 375 Degrees Fahrenheit. Set pressure at heavy 45 - 55 lbs. Print 8 - 10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion. Light colors only.

Updated 5 years ago by Nathan Reedy

Sparkle Puff Application Instructions

Set temperature at 365-375 degrees Fahrenheit. Set pressure at medium to heavy pressure. Print 6-8 seconds. Peel warm (wait about 5 seconds), in one continuous, smooth rapid motion.

Updated 5 years ago by Nathan Reedy

Spot Color With Metallic Application Instructions

Application Instructions. Set temperature at 375-385 degrees Fahrenheit. Set pressure at medium/heavy pressure. Print 8-10 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion.

Updated 5 years ago by Nathan Reedy

SubliFab with Rhinestuds Application Instructions

Pre-press garment; 5-7 seconds. Peel the white sheet and discard. Place sticky side down on the garment. Set pressure at heavy. Set temperature at 350 degrees Fahrenheit. Print 8 seconds. Peel warm (…

Updated 5 years ago by Nathan Reedy

Supacolor Wearable Application Instructions

Application Instructions Pre-press garment; 5-10 seconds. Set temperature at 290-320 degrees Fahrenheit. Set to heavy pressure. Heavy as possible with still being able to close your press. Press 10-1…

Updated 9 months ago by Nathan Reedy

Texprint Sublimation Paper on Sequins

Application Instructions Set temperature to 400 degrees Fahrenheit. Set timer to 45-55 seconds. Set Pressure at medium. Print a mirror image onto Texprint Paper. Flip all sequins over to so the white…

Updated 3 years ago by Nathan Reedy

VibraTrans Application Instructions

Pre-press garment; 5-7 seconds. Set temperature at 375 degrees Fahrenheit. Set pressure to heavy. Print for 7 seconds. Peel immediately while hot, in one continuous, smooth, rapid motion. Click Here…

Updated 4 years ago by Nathan Reedy

Warm Peel Application Instructions

Pre-press garment; 5-7 seconds. Set pressure at high. Set temperature at 385 deg. Fahrenheit. Print 8-10 seconds. Peel warm (wait about 5 seconds), in one continuous, smooth rapid motion.

Updated 5 years ago by Nathan Reedy